Drain completely and rinse well with water. Larger gas tank de-rusting: Pour in 5 litres of EVAPO-RUST® and rotate gas tank every hour until the rust has been removed.Air dry and fill with gasoline immediately to eliminate flash rust. Smaller gas tank de-rusting: Completely fill the tank with EVAPO-RUST® and allow to sit for 2 to 4 hours.Rusty tools, hardware, automotive parts, household items, antiques, equipment.Will not affect plastic, PVC, Viton and non-oxide-based paints.Will not harm unrusted steel, safe on other metals.No fumes or bad odours, non-flammable, no VOCs.SAFE TO USE: This metal rust remover is made of a non-toxic and water-based solution that is easy-to-use on automotive, household and industrial-grade metal parts. Powerful heavy-duty formula for even the toughest rust EVAPO-RUST RUST REMOVER: Evapo-Rust effortlessly removes rust from automotive parts, hardware, tools, cookware, and antiques without any scrubbing or sanding.No need for mixing, the solution is ready to use. The award-winning formula is specifically designed to remove rust, with no scrubbing or sanding required. I was playing with a new product and it showed me why I should not have done it.Evapo-Rust® is a non-toxic rust remover for fast and effective restoration. When I removed it, the bluing was gone on any part that was in the chemical.Ī very stupid mistake on my part as the rust that was there could have been removed with Kroil and some 0000 steel wool. I went into the house and returned about 15 minutes later to find my gun all the way into the Evapo-Rust. I put some light wire around the grip and inserted the gun to where it was just touching. I have a High Standard 22 magnum derringer and it had rust on the end of the barrels. I will give you a warning about this great product though. I purchased some old rusted tools at a garage sale and they look like new now. I have yet found anything that it fails to work on. You might want to check Wally World also. Evapo-Rust rust remover is an environmentally safe, water based product that has. It is safe on all surfaces and will not harm copper, brass.
Simply dip your part or tool in the solution and let sit for an hour to overnight depending on the depth of rust. Evapo-Rust Rust Removal Evapo-rust is a super safe rust remover that will remove rust safely form antiques, automorive parts, cast iron cookware, hardware. Evapo-Rust Gel is proven effective to remove even deep rust on all types of mild steel and iron. If Jamie purchased it for such a low price then I would go there. Evaporust Super Safe Rust Remover - Silver (1L) code. The price they quote is 18.99 now and I think I paid about $12 so it has increased. Doesn't get much simpler than that.Įvapo-Rust was purchased by me about 18 months ago from Midway in a gallon bottle. Use was absolutely simple: Put the product in the solution overnight, rinse the next day, and coat in oil. I believe it cost around $7.00 at O'Reiley's Auto Parts. I coated the first block with Kroil.įrom my experience, I would absolutely recommend this product. It looks fantastic.Īfter taking the pic, I put the other block, sprue plate, and hardware in the solution. This is how the worst looking block turned out. This is how I just took it out.īut the real success was in the cavities. So I left the mould in the solution overnight. I rolled the it over and placed it back in the solution. However, I still had a slight rusting on the exterior of the mould and the cavitites still had a little rust. I would say that 90% of the block was amazing. The results: After 1/2 hour, this is how the mould looked. Using a plastic storage container from Dollar Tree, I placed the mould on the bottom and poured enough Evapo-Rust in to cover the mould by about 1/4". This is the product package and the mould in question. A product of extensive research, Evapo-Rust(R) rust remover is an environmentally safe water based product that has been proven to make even deep rust. This would give me (hopefully) the most drastic transformation. I decided to do the worst looking block of the two. I am almost ashamed to post these before pictures. When I checked the mould a few days ago, I noticed some rust in the cavities. From the first time I used it, the mould flash rusted but the cavities remained in good shape. In October 2008, I purchased a new Lyman 4 cavity mould (Cut Aug 08). This has worked for me with Saeco, Modern Bond, Ideal, Lyman, RCBS, and Cramer moulds. Also to know is, How do you clean rust off of iron. Since North Dakota isn't exactly known as a humid environment, I typically cast in my shed and let the moulds cool down on their own overnight, recovering them the next day. Following are the directions to use vinegar for removing rust from iron objects. I have a problem with one mould in particular, so I decided to give it a try. I read on the forum of some folks using a product called Evapo-Rust to get rust out of their moulds.